Tracing

Real-time inspection

Introduction

When working with a system like VerneMQ sometimes when troubleshooting it would be nice to know what a client is actually sending and receiving and what VerneMQ is doing with this information. For this purpose VerneMQ has a built-in tracing mechanism which is safe to use in production settings as there is very little overhead in running the tracer and has built-in protection mechanisms to stop traces that produce too much information.

Tracing clients

To trace a client the following command is available:

vmq-admin trace client client-id=<client-id>

See the available flags by calling vmq-admin trace client --help.

A typical trace could look like the following:

$ vmq-admin trace client client-id=client
No sessions found for client "client"
New session with PID <7616.3443.1> found for client "client"
<7616.3443.1> MQTT RECV: CID: "client" CONNECT(c: client, v: 4, u: username, p: password, cs: 1, ka: 30)
<7616.3443.1> Calling auth_on_register({{172,17,0,1},34274},{[],<<"client">>},username,password,true) 
<7616.3443.1> Hook returned "ok"
<7616.3443.1> MQTT SEND: CID: "client" CONNACK(sp: 0, rc: 0)
<7616.3443.1> MQTT RECV: CID: "client" SUBSCRIBE(m1) with topics:
    q:0, t: "topic"
<7616.3443.1> Calling auth_on_subscribe(username,{[],<<"client">>}) with topics:
    q:0, t: "topic"
<7616.3443.1> Hook returned "ok"
<7616.3443.1> MQTT SEND: CID: "client" SUBACK(m1, qt[0])
<7616.3443.1> Trace session for client stopped

In this particular trace a trace was started for the client with client-id client. At first no clients are connected to the node where the trace has been started, but a little later the client connects and we see the trace come alive. The strange identifier <7616.3443.1> is called a process identifier and is the identifier of the process in which the trace happened - this isn't relevant unless one wants to correlate the trace with log entries where process identifiers are also logged. Besides the process identifier there are some lines with MQTT SEND and MQTT RECV which are to be understood from the perspective of the broker. In the above trace this means that first the broker receives a CONNECT frame and replies with a CONNACK frame. Each MQTT event is annotated with the data from the MQTT frame to give as much detail and insight as possible.

Notice the auth_on_register call between CONNECT and CONNACK which is the authentication plugin hook being called to authenticate the client. In this case the hook returned ok which means the client was successfully authenticated.

Likewise notice the auth_on_subscribe call between the SUBSCRIBE and SUBACK frames which is plugin hook used to authorize if this particular subscription should be allowed or not. In this case the subscription was authorized.

Trace options

The client trace command has additional options as shown by vmq-admin trace client --help. Those are hopefully self-explaining:

Options

  --mountpoint=<Mountpoint>
      the mountpoint for the client to trace.
      Defaults to "" which is the default mountpoint.
  --rate-max=<RateMaxMessages>
      the maximum number of messages for the given interval,
      defaults to 10.
  --rate-interval=<RateIntervalMS>
      the interval in milliseconds over which the max number of messages
      is allowed. Defaults to 100.
  --trunc-payload=<SizeInBytes>
      control when the payload should be truncated for display.
      Defaults to 200.

A convenient tool is the ts (timestamp) tool which is available on many systems. If the trace output is piped to this command each line is prefixed with a timestamp:

ts | sudo vmq-admin trace client client-id=tester

It is currently not possible to start multiple traces from multiple shells, or trace multiple ClientIDs.

Last updated